资源列表

« 1 2 ... .87 .88 .89 .90 .91 1592.93 .94 .95 .96 .97 ... 4311 »

[VHDL编程Axi_mux

说明:The elements come from the necessity of creating generic modules, in the verification phase, for this widely used protocol. These primitives are presented as a not compiled library written in SystemC where interf
<Paul Stephen> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程I2C-24C01

说明:AVR twi读写eeprom的程序及驱动-AVR twi read and write eeprom program and driver
<姜迁里> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程8.9-ASK-debug-VHDL-program

说明:基于VHDL硬件描述语言,对基带信号进行ASK调制-VHDL hardware descr iption language based on ASK modulation baseband signal
<HUANGTIANWEN> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程CC2530_PWM

说明:基于cc2530的生成PWM波程序,自动调节占空比,以调节节能灯的亮度。-Based on the formation of the program cc2530 PWM waves, automatic regulation occupies emptiescompared to adjust the brightness of the energy-saving lamps.
<扬惠普> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程ASK

说明:ASK调制与解调的VHDL源程序 附带仿真-ASK modulation and demodulation of the VHDL source code with simulation
<> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程cfi_ctrl_latest.tar

说明:很好的 wishbone转CFI FLASH接口的源码,在INTERL的FLASH上已经调试通过-CFI FLASH CORE
<sunhuaiyi> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程EXP3

说明:FPGA系统设计,初学者的好工具。可以更快的上手入门。-FPGA system design, beginners of practice good tools
<chenshi> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程XC3S400

说明:XC3S400 minimum system with XCF02S platform flash very useful
<mosi> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程2048Mb_ddr3

说明:美光DDR3存储器模型,用verilog语言编写,通用模型-DDR3 MEMORY
<AricSnow> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程_3_rider_led

说明:3 rider_led verilog实例3跑马灯 (1)源文件 rider_led.v (2)管脚分配 pins list.txt -3 rider_led 跑马灯 (1)源文件 rider_led.v (2)管脚分配 pins list.txt
<李程序> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程_4_water_led

说明:verilog实例4 water_led 流水灯 (1)源文件 water_led.v (2)管脚分配 pins list.txt -4 water_led 流水灯 (1)源文件 water_led.v (2)管脚分配 pins list.txt
<李程序> 在 2025-03-12 上传 | 大小:41kb | 下载:0

[VHDL编程Double-byte-adder-BCD-code

说明:将以片内RAM 30H 为起始地址的双字节BCD码 30H和40H为起始地址的双字节BCD码相加,结果放在50H和51H中,程序结束-Will be in RAM30H for the starting address of the double byte BCD code 30H and 40H for the starting address of the double byte BCD code phase, results in
<刘智平> 在 2025-03-12 上传 | 大小:41kb | 下载:0
« 1 2 ... .87 .88 .89 .90 .91 1592.93 .94 .95 .96 .97 ... 4311 »

源码中国 www.ymcn.org