文件名称:ADC
- 所属分类:
- 单片机(51,AVR,MSP430等)
- 资源属性:
- [C/C++] [源码]
- 上传时间:
- 2012-11-26
- 文件大小:
- 75kb
- 下载次数:
- 0次
- 提 供 者:
- vin****
- 相关连接:
- 无
- 下载说明:
- 别用迅雷下载,失败请重下,重下不扣分!
介绍说明--下载内容均来自于网络,请自行研究使用
HCS908_QG8 单片机开发板ADC实验介绍:
本程序是ADC模块的例程,所用资源为单片机内部ADC转换模块,所接器件为电位器.
实验现象:
在仿真界面的DATA1窗口中观察mm的值是否随电位器输出值变化而变化
-Singlechip HCS908_QG8 development board ADC Experimental descr iption: This procedure is the ADC module s routines, the resources used for the internal ADC conversion single-chip module, the access device for the potentiometer. Experimental phenomena: In the simulation interface window DATA1 observed mm With the potential value of the output value changes
(系统自动生成,下载前可以参看下载内容)
下载文件列表
ADC
...\ADC_Data
...\........\CWSettingsWindows.stg
...\........\Standard
...\........\........\ObjectCode
...\........\........\..........\main.c.o
...\........\........\..........\MC9S08QG8.C.o
...\........\........\..........\Start08.c.o
...\........\........\TargetDataWindows.tdt
...\bin
...\...\Project.abs
...\...\Project.abs.s19
...\...\Project.map
...\...\Project.s19
...\...\Project.xpr
...\cmd
...\...\BDM_P&E_Multilink_CyclonePro_Postload.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Preload.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Reset.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Startup.cmd
...\...\HCS08_OpenSourceBDM_Erase_Unsecure.cmd
...\...\HCS08_OpenSourceBDM_Postload.cmd
...\...\HCS08_OpenSourceBDM_Preload.cmd
...\...\HCS08_OpenSourceBDM_Reset.cmd
...\...\HCS08_OpenSourceBDM_Startup.cmd
...\C_Layout.hwl
...\Default.mem
...\HCS08_OpenSourceBDM.ini
...\prm
...\...\burner.bbl
...\...\Project.prm
...\Sources
...\.......\derivative.h
...\.......\main.c
...\.......\Start08.c
...\ADC_Data
...\........\CWSettingsWindows.stg
...\........\Standard
...\........\........\ObjectCode
...\........\........\..........\main.c.o
...\........\........\..........\MC9S08QG8.C.o
...\........\........\..........\Start08.c.o
...\........\........\TargetDataWindows.tdt
...\bin
...\...\Project.abs
...\...\Project.abs.s19
...\...\Project.map
...\...\Project.s19
...\...\Project.xpr
...\cmd
...\...\BDM_P&E_Multilink_CyclonePro_Postload.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Preload.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Reset.cmd
...\...\BDM_P&E_Multilink_CyclonePro_Startup.cmd
...\...\HCS08_OpenSourceBDM_Erase_Unsecure.cmd
...\...\HCS08_OpenSourceBDM_Postload.cmd
...\...\HCS08_OpenSourceBDM_Preload.cmd
...\...\HCS08_OpenSourceBDM_Reset.cmd
...\...\HCS08_OpenSourceBDM_Startup.cmd
...\C_Layout.hwl
...\Default.mem
...\HCS08_OpenSourceBDM.ini
...\prm
...\...\burner.bbl
...\...\Project.prm
...\Sources
...\.......\derivative.h
...\.......\main.c
...\.......\Start08.c