文件名称:DISPLAY
介绍说明－－下载内容均来自于网络，请自行研究使用
本程序是显示模块的例程，所接器件为四位八段led数码管，其中PTB0-PTB3
与数码管的位选相连接，PTB4，PTB5与74LS164连接确定你开发板上拨码开
关JP1（图片上的12）的两位和JP4（图片上的9）的5、6、7、8位处于on），
而其他位处于远离on！-This procedure is the routine display module, the access device for four eight led digital tube, which PTB0-PTB3 bit digital tube and connected to the election, PTB4, PTB5 with 74LS164 sure you connect the development of on-board DIP switch JP1 ( picture on the 12) two and JP4 (picture on the 9) of 5,6,7,8 located at on), while the other located at far away from the on!
与数码管的位选相连接，PTB4，PTB5与74LS164连接确定你开发板上拨码开
关JP1（图片上的12）的两位和JP4（图片上的9）的5、6、7、8位处于on），
而其他位处于远离on！-This procedure is the routine display module, the access device for four eight led digital tube, which PTB0-PTB3 bit digital tube and connected to the election, PTB4, PTB5 with 74LS164 sure you connect the development of on-board DIP switch JP1 ( picture on the 12) two and JP4 (picture on the 9) of 5,6,7,8 located at on), while the other located at far away from the on!
(系统自动生成,下载前可以参看下载内容)
下载文件列表
DISPLAY
.......\BDM_P&E_Multilink_CyclonePro.ini
.......\bin
.......\...\Project.abs
.......\...\Project.abs.s19
.......\...\Project.map
.......\cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Postload.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Preload.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Reset.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Startup.cmd
.......\...\HCS08_Full_Chip_Simulator_Postload.cmd
.......\...\HCS08_Full_Chip_Simulator_Preload.cmd
.......\...\HCS08_Full_Chip_Simulator_Reset.cmd
.......\...\HCS08_Full_Chip_Simulator_Startup.cmd
.......\...\HCS08_OpenSourceBDM_Erase_Unsecure.cmd
.......\...\HCS08_OpenSourceBDM_Postload.cmd
.......\...\HCS08_OpenSourceBDM_Preload.cmd
.......\...\HCS08_OpenSourceBDM_Reset.cmd
.......\...\HCS08_OpenSourceBDM_Startup.cmd
.......\C_Layout.hwl
.......\Default.mem
.......\DISPLAY.mcp
.......\DISPLAY_Data
.......\............\CWSettingsWindows.stg
.......\............\Standard
.......\............\........\ObjectCode
.......\............\........\..........\main.c.o
.......\............\........\..........\MC9S08QG8.C.o
.......\............\........\..........\Start08.c.o
.......\............\........\TargetDataWindows.tdt
.......\HCS08_Full_Chip_Simulator.ini
.......\HCS08_OpenSourceBDM.ini
.......\prm
.......\...\burner.bbl
.......\...\Project.prm
.......\Sources
.......\.......\derivative.h
.......\.......\main.c
.......\.......\Start08.c
.......\BDM_P&E_Multilink_CyclonePro.ini
.......\bin
.......\...\Project.abs
.......\...\Project.abs.s19
.......\...\Project.map
.......\cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Postload.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Preload.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Reset.cmd
.......\...\BDM_P&E_Multilink_CyclonePro_Startup.cmd
.......\...\HCS08_Full_Chip_Simulator_Postload.cmd
.......\...\HCS08_Full_Chip_Simulator_Preload.cmd
.......\...\HCS08_Full_Chip_Simulator_Reset.cmd
.......\...\HCS08_Full_Chip_Simulator_Startup.cmd
.......\...\HCS08_OpenSourceBDM_Erase_Unsecure.cmd
.......\...\HCS08_OpenSourceBDM_Postload.cmd
.......\...\HCS08_OpenSourceBDM_Preload.cmd
.......\...\HCS08_OpenSourceBDM_Reset.cmd
.......\...\HCS08_OpenSourceBDM_Startup.cmd
.......\C_Layout.hwl
.......\Default.mem
.......\DISPLAY.mcp
.......\DISPLAY_Data
.......\............\CWSettingsWindows.stg
.......\............\Standard
.......\............\........\ObjectCode
.......\............\........\..........\main.c.o
.......\............\........\..........\MC9S08QG8.C.o
.......\............\........\..........\Start08.c.o
.......\............\........\TargetDataWindows.tdt
.......\HCS08_Full_Chip_Simulator.ini
.......\HCS08_OpenSourceBDM.ini
.......\prm
.......\...\burner.bbl
.......\...\Project.prm
.......\Sources
.......\.......\derivative.h
.......\.......\main.c
.......\.......\Start08.c