文件名称:YS-1(20141119V1.1)
- 所属分类：
- 单片机(51,AVR,MSP430等)
- 资源属性：
- [C/C++] [源码]
- 上传时间：
- 2016-12-12
- 文件大小：
- 44kb
- 下载次数：
- 0次
- 提 供 者：
- s**
- 相关连接：
- 无
- 下载说明：
- 别用迅雷下载，失败请重下，重下不扣分！
下载
别用迅雷、360浏览器下载。
如迅雷强制弹出，可右键点击选“另存为”。
失败请重下，重下不扣分。
如迅雷强制弹出，可右键点击选“另存为”。
失败请重下，重下不扣分。
介绍说明－－下载内容均来自于网络，请自行研究使用
继电器输出端：
1、NO： 继电器常开接口，继电器吸合前悬空，吸合后与COM短接
2、COM：继电器公用接口
3、NC： 继电器常闭接口，继电器吸合前与COM短接，吸合后悬空
名词解析：
长锁：P1端口收到低电平后，继电器就一直导通，直到模块断电，才关闭。
自锁：P2端口收到低电平后，继电器导通，再次收到低电平，继电器关闭。
延时30s：P3端口收到低电平后，继电器导通30s后自动关闭，再收到低电平，再延时30s
-Relay output:
1, NO: relay normally open interface, the relay pull before the open, after the short-circuit with the COM
2, COM: relay common interface
3, NC: normally closed relay interface, the relay before the short circuit with the COM, pull after the vacant
Noun:
Long lock: P1 port received a low level, the relay has been conductive until the module power, only closed.
Self-locking: P2 port receives a low level, the relay conduction, once again received low, the relay is turned off.
Delay 30s: P3 port received a low level, the relay turns on automatically after 30s, then received low, and then delay 30s
1、NO： 继电器常开接口，继电器吸合前悬空，吸合后与COM短接
2、COM：继电器公用接口
3、NC： 继电器常闭接口，继电器吸合前与COM短接，吸合后悬空
名词解析：
长锁：P1端口收到低电平后，继电器就一直导通，直到模块断电，才关闭。
自锁：P2端口收到低电平后，继电器导通，再次收到低电平，继电器关闭。
延时30s：P3端口收到低电平后，继电器导通30s后自动关闭，再收到低电平，再延时30s
-Relay output:
1, NO: relay normally open interface, the relay pull before the open, after the short-circuit with the COM
2, COM: relay common interface
3, NC: normally closed relay interface, the relay before the short circuit with the COM, pull after the vacant
Noun:
Long lock: P1 port received a low level, the relay has been conductive until the module power, only closed.
Self-locking: P2 port receives a low level, the relay conduction, once again received low, the relay is turned off.
Delay 30s: P3 port received a low level, the relay turns on automatically after 30s, then received low, and then delay 30s
(系统自动生成,下载前可以参看下载内容)
下载文件列表
YS-1路延时继电器--程序工程(20141119V1.1)\app\YS_time.uvopt
........................................\...\YS_time.uvproj
........................................\...\YS_time_uvopt.bak
........................................\...\YS_time_uvproj.bak
........................................\code\fyy_config.h
........................................\....\STC15.h
........................................\....\STC15_USART1.c
........................................\....\STC15_USART1.h
........................................\....\YS-M1.C
........................................\obj\STC15_Delay.lst
........................................\...\STC15_Delay.obj
........................................\...\STC15_USART1.lst
........................................\...\STC15_USART1.obj
........................................\...\YS-M1.lst
........................................\...\YS-M1.obj
........................................\...\YS_M1.LIB
........................................\...\YS_M1.plg
........................................\...\YS_M1.__b
........................................\...\YS_time
........................................\...\YS_time.hex
........................................\...\YS_time.lnp
........................................\...\YS_time.m51
........................................\...\YS_time.plg
........................................\user\STC15_Delay.c
........................................\....\STC15_Delay.h
........................................\app
........................................\code
........................................\obj
........................................\user
YS-1路延时继电器--程序工程(20141119V1.1)