资源列表

[单片机(51,AVR,MSP430等)时钟成品12864fei

说明:利用ds1302,显示年月日时分秒,按键调节时间数据,显示在128864液晶显示屏上。(The use of DS1302, display the date when, button adjustment time data displayed on the LCD screen in 128864.)
<追月的风> 在 2025-02-04 上传 | 大小:132kb | 下载:0

[单片机(51,AVR,MSP430等)旋转LED立体平面显示字程序

说明:旋转LED立体平面显示字程序,可以修改任意文字。、....................(Rotary LED stereoscopic plane display word program)
<lxy-love> 在 2025-02-04 上传 | 大小:64kb | 下载:0

[单片机(51,AVR,MSP430等)基础-LRC

说明:LRC 串行通讯Labview串行通讯专题讲座介绍(Labview LRC 485 serial communication Labview serial communication seminar introduction.)
<sun211> 在 2025-02-04 上传 | 大小:11kb | 下载:0

[其他嵌入式/单片机内容XBee_API_Example

说明:Xbee API Example can be used to understand how xbee works by using Arduino
<parinyax> 在 2025-02-04 上传 | 大小:1.62mb | 下载:0

[嵌入式/单片机编程lwip-master

说明:lwip TCP 协议栈,内涵PPP通讯协议(LwIP TCP protocol stack, connotations PPP communication protocol)
<smallmice> 在 2025-02-04 上传 | 大小:686kb | 下载:0

[单片机(51,AVR,MSP430等)实例8 RTC实验

说明:可通过更改代码设定自己需要的时间,闹钟,设定完成后,代码会自动进行时间的增加,并且有年月日的显示(By changing the code to set the time you need, the alarm clock, when the set is complete, the code will automatically increase the time, and there are days and months of d
<infinite卷毛> 在 2025-02-04 上传 | 大小:3.72mb | 下载:0

[单片机(51,AVR,MSP430等)DMXSerial-master

说明:arduino DMX
<Neung> 在 2025-02-04 上传 | 大小:19kb | 下载:0

[微处理器(ARM/PowerPC等)RealBoard4088-master

说明:CMSIS Drivers CAN Driver for the LPC17xx series
<wakaw> 在 2025-02-04 上传 | 大小:42.67mb | 下载:0

[VHDL编程Guia_1B

说明:0-10-0 counter to 8051 microcontroller in assembly
<ruimartins123> 在 2025-02-04 上传 | 大小:28kb | 下载:0

[嵌入式/单片机编程程序1

说明:长按引脚输出高电平,再次长按该引脚输出低电平(Long according to pin output high level, again long press the pin to output low level)
<longshaoye12> 在 2025-02-04 上传 | 大小:29kb | 下载:0

[单片机(51,AVR,MSP430等)C51_code

说明:再51单片机上玩俄罗斯方块,里面的说明注解都非常详细(I play the Tetris block on the 51 single chip, and the explanatory notes are very detailed.)
<小浩001> 在 2025-02-04 上传 | 大小:14kb | 下载:0

[单片机(51,AVR,MSP430等)serial_switch

说明:通过串口发送命令,控制IO口变低,2秒后,IO口电平变高,2秒是通过定时器控制的,时间比较精确(The command is sent through the serial port to control the lower IO port. After 2 seconds, the level of the IO port becomes higher, and the 2 second is controlled by the ti
<xiewensheng> 在 2025-02-04 上传 | 大小:19kb | 下载:0

源码中国 www.ymcn.org