[DSP编程] CSharp-(2)

说明：c#的教程，怎么做界面，包括教程和代码，代码都能运行，实测过。-C# tutorial, how to do the interface, including tutorials and code, the code can run, measured over.
<毕刚> 在 2025-02-25 上传 | 大小：46.35mb | 下载：0

[VHDL编程] cla_16bit

说明：verilog 16bit carry lookahead adder-verilog 16bit carry lookahead adder
<uiop7890> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[VHDL编程] qiangda

说明：抢答器，3人进行抢答，即对应三个开关，谁先按下，LED输出显示-Responder, 3 answer, that corresponds to three switches, who first press, LED output display
<樊雪婵> 在 2025-02-25 上传 | 大小：1.76mb | 下载：0

[其他嵌入式/单片机内容] ADC_of_MSP430F249

说明：A single sample is made on A10 with reference to internal 1.5V Vref. Software sets ADC12SC to start sample and conversion - ADC12SC automatically cleared at EOC. ADC12 internal oscillator times sample and conversio
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] TimerA_of_MSPF249

说明：Toggle P1.0 using software and the TA_0 ISR. Timer_A is configured for up mode, thus the timer overflows when TAR counts to CCR0. In this example, CCR0 is loaded with 1000-1. ACLK = TACLK = INCLK = 32768Hz, MCLK =
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] I2C_of_MSP430F249

说明：This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt i
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] SPI_of_MSP430F249

说明： SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is use
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] UART_of_MSP430F249

说明： Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] FLASH_WRITE_of_MSP430

说明： This program first erases flash seg C, then it increments all values in seg C, then it erases seg D, then copies seg C to seg D. Seg C @ 1040h Seg D @ 1000h The EEI bit is set for the Flash Erase Cycles. This does
<sattarhastam> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[单片机(51,AVR,MSP430等)] xiaoche

说明：自动循迹小车 测速 可检测金属 LCD显示路程时间-Automatic tracking car can detect metal LCD display distance
<冯立彬> 在 2025-02-25 上传 | 大小：37kb | 下载：0

[其他嵌入式/单片机内容] zephyr_sensor

说明：基于Zephyr v1.7.0开发的MPU6050 sensor读取程序，MPU6050的驱动位置zephyr目录zephyr-v1.7.0/drivers/sensor/mpu6050-MPU6050 sensor application base on Zephyr v1.7.0, the MPU6050 driver is under zephyr-v1.7.0/drivers/sensor/mpu6050
<韦伯> 在 2025-02-25 上传 | 大小：1kb | 下载：0

[其他嵌入式/单片机内容] zephyr_thread

说明：threads, semaphore and interrupt application on zephyr，按下按键后能够区分长按或者短按，并通过semaphore让相应thread得以继续运行，通过串口和LED显示长按和短按结果-threads, semaphore and interrupt application on zephyr, the application can recognize hold and short pr
<韦伯> 在 2025-02-25 上传 | 大小：1kb | 下载：0