资源列表

« 1 2 ... .48 .49 .50 .51 .52 24953.54 .55 .56 .57 .58 ... 33935 »

[嵌入式Linuxmini6410-led

说明:Mini6410的LED裸机开发程序,源代码-Mini6410 development process of the LED bare metal, the source code
<徐路> 在 2025-02-28 上传 | 大小:23kb | 下载:0

[其他嵌入式/单片机内容CUI

说明:手机超炫的桌面系统,需要集成加入源码编译。-Mobile stunning desktop system, you need to add source compiler integration.
<李明军> 在 2025-02-28 上传 | 大小:120kb | 下载:0

[VHDL编程pci_mini_latest.tar

说明:PCI代码,verilog,简单的PCI设计,使用FPGA实现-PCI code, verilog, simple PCI design, FPGA implementation
<long jinbo> 在 2025-02-28 上传 | 大小:514kb | 下载:0

[其他嵌入式/单片机内容1

说明:单片机滚动显示 C51程序 综合实验二十字-C51 microcontroller rolling display program
<lijunhua> 在 2025-02-28 上传 | 大小:20kb | 下载:0

[VHDL编程Adept-IOExpansion

说明:digilent ioexpansion
<suresh> 在 2025-02-28 上传 | 大小:57kb | 下载:0

[Windows CEUniStrongDemo

说明:wince gps demo 调用gps的接口实现定位,路径分析-wince gps demo
<sdfg> 在 2025-02-28 上传 | 大小:14.1mb | 下载:0

[单片机(51,AVR,MSP430等)MSP430-control-TLV5613

说明:这个是用MSP430单片机驱动12bit并口数模转换器TLV5613的例子程序。程序中sent_data = 0x0fff,输出模拟电压为最*值。-This is done using the parallel port MSP430 microcontroller driver 12bit DAC TLV5613 example program. Program sent_data = 0x0fff, the analog out
<xiaogong> 在 2025-02-28 上传 | 大小:19kb | 下载:0

[单片机(51,AVR,MSP430等)M1

说明:连接在无极性的二总线上,用于监控压力开关等输出开关量信号的设备。-Promise of the two connected on the bus for monitoring pressure switch output switch signal equipment.
<揭晓洪> 在 2025-02-28 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)M2

说明:实时监控并接收主机发出的控制命令,启动相应的设备。-Real-time monitoring and control commands issued by the receiving host, start the appropriate equipment.
<揭晓洪> 在 2025-02-28 上传 | 大小:6kb | 下载:0

[单片机(51,AVR,MSP430等)M32

说明:用于实时监控一定范围内的烟雾变化,并把状态通过无极性二总线传输给主机。-For real-time monitoring of a range of smoke changes, and the state of polarity of the second bus through transmission to the host.
<揭晓洪> 在 2025-02-28 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)R8CL35_TimerC_PWM_Ext8M_Div8

说明:瑞萨芯片学习代码,对于入门的有一定的帮助-Renesas chip learning code, for the entry of some help
<陈陈> 在 2025-02-28 上传 | 大小:471kb | 下载:0

[单片机(51,AVR,MSP430等)2

说明:通电启动后,默认状态是读出E2PROM中保存的电机走纸的长度并显示,显示的走纸长度可以通过键盘重新设置-After power-up, the default state is stored in E2PROM read the paper feed motor length and display, the displayed paper feed length can be reset via the keyboard
<> 在 2025-02-28 上传 | 大小:1kb | 下载:0
« 1 2 ... .48 .49 .50 .51 .52 24953.54 .55 .56 .57 .58 ... 33935 »

源码中国 www.ymcn.org