资源列表

« 1 2 ... .02 .03 .04 .05 .06 214107.08 .09 .10 .11 .12 ... 216430 »

[C#编程gaosigongshi

说明:四阶高斯公式的程序,基于c语言开发,使程序-gauss
<薛林> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)sy_010

说明:定时器1工作于16位计数模式,记录外部脉冲的个数,定时器0工作于定时模式,用于进行动态扫描显示-Timer 1 works in 16-bit counter mode, recording the number of external pulse, timer 0 working in regular mode, is used for dynamic scanning display
<薛林> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)SY_001

说明:流水灯演示程序 适用于CC100A、CC100B、CC100C。请注意引脚接线-Water lights demo program applies to CC100A, CC100B, CC100C. Please note that pin connection
<薛林> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[matlab例程rbf

说明:RBF神经网络利用MATLAB工具箱函数实现非线性函数回归-RBF neural network using MATLAB toolbox function is to achieve non-linear regression function
<心心> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[数值算法/人工智能crc7

说明:CRC计算模块,7位CRC计算。经过FPGA及IC平台验证。-CRC calculation module, 7 CRC calculation. Through the FPGA and IC platform for verification.
<liu> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[数值算法/人工智能crc16

说明:CRC16模块,用于SD卡驱动设计。经过FPGA及IC平台验证。-CRC16 module for SD card-driven design. Through the FPGA and IC platform for verification.
<liu> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)anjiansaomiao

说明:按键扫描程序,上电时, 点亮P00口LED,操作室注意结对引脚-Key scanner, operating room pay attention to the pin junction
<薛林> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[数值算法/人工智能divider

说明:流水型除法器,经过FPGA平台验证。宽度可以任意修改,提供计算完毕信号。-Water-type divider, after a FPGA platform validation. Width can be modified to provide the calculation is completed the signal.
<liu> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[数值算法/人工智能hex_vs_asic

说明:hex到asic,以及asic到hex的verilog转换模块,全组合逻辑,单周期完成。-hex to asic, as well as the asic to the hex of the verilog conversion module, the whole combination of logic, single-cycle completion.
<liu> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)AD976

说明:使用keil 开发,是一款16位AD,精度高,用C8051F020开发。-Use keil development, is a 16-bit AD, high precision, with the C8051F020 development.
<linhai> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)24CXX

说明:I2C EEPROM 24C读写器源文件,一个读写程序-I2C EEPROM 24C reader the source file, a reading and writing program
<薛林> 在 2025-03-15 上传 | 大小:1kb | 下载:0

[其他行业RA

说明:本fortran程序是重磁滑动平均算法的程序。-The fortran program is gravity and magnetic moving average algorithm procedure.
<sunfeng> 在 2025-03-15 上传 | 大小:1kb | 下载:0
« 1 2 ... .02 .03 .04 .05 .06 214107.08 .09 .10 .11 .12 ... 216430 »

源码中国 www.ymcn.org