搜索资源列表
LED1.zip
- 汇编静态灯显示
6.GPIO输出实验-LED数码管
- EasyARM2131开发板源码之一-----------6.GPIO输出实验-LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值-EasyARM2131 one source development board ----------- 6.GPIO experimental output - digital LED Display 0-F characters and control LE
最基本的试验44B0下面LED1
- 入门试验代码，可能这几个试验代码的前面启动不风都是一样的但是中间的不风还是有写不一样的，这个时很基本的入门试验，点亮LED-entry test code, this may be a few test code does not start ahead of the wind are the same but the middle of the wind was still not the same, at the very basi
DATARETa
- 发送和接收到的数据一样多，边接边返回到上位机，使用串口UART0接收上位机发送的数据，接收到和发送的数据一样多后，取反LED1控制，并将数据原封不动地发送回上位机。 周立功lpc2104开发板开发-to send and receive data as much side to side to take MCS96/98 use Serial UART0 receiving PC to send data, receive and
DATARETljx
- LED数码管显示0-F字符，同时控制LED1、LED2、LED3、LED4显示对应的16进行值。数据以高低位调换. 串口UART0接收上位机发送的数据，接收到返回最后一个数据到上位机，同时中断计数显示，显示回发上位机的数据。 周立功lpc2104板开发。-digital LED Display 0-F characters and control LED1, LED2, LED3. LED4 shows the correspond
qianrushixitongzuoye
- 嵌入式系统作业。本实验是编写程序，控制实验平台的发光二级管LED1、LED2、LED3、LED4，使它们有规律地点亮和熄灭。-Embedded operating system. The experimental procedure is the preparation and control platform of the two luminescence LED1, LED2, indicates that LED4. make t
WriteLCD
- dspic的汇编例程，Write LCD with text using PSV feature and flash LED1 with a Timer1 loop-dspic compilation routines. Write text using LCD with PSV feature and flash L ED1 with a loop Timer1
44test
- ledtest,ads1.2 led0,led1,led2依次点亮-ledtest, ads1.2 led0, led1, were lit led2
44test
- ledtest,ads1.2 led0,led1,led2依次点亮-ledtest, ads1.2 led0, led1, were lit led2
LED1
- 控制灯的各种工作方式，使灯能够按照各种方式工作，当然，只要稍作修改，便可以完成其他功能 -Control the various lights work, so that lights can work in accordance with a variety of ways, of course, as long as some slight modifications, we can complete other functio
led1
- LED显示屏灰度设计相关, 很有参考价值啊(1)-LED display gray design, a good reference value ah (1)
led1
- 一种汇编的16F877控制595的LED屏源程序-16F877 to control a compilation of 595 of the LED screen source
S
- 时钟显示程序，一共八个LED led7-8显示小时，LED6显示- LED4-5显示分钟，LED3显示-，LED1-2显示秒-RETRETRETRETRETRETRETRETRETRETRETTRETRETRETRETRETRET
LED1
- 【实验题目】 流水灯LED 【实验目的】 复习巩固定时器的用法。 学习怎样用74HC573扩展简单的并行输出端口。 【硬件接法】 以74HC573扩展输出端口的方法驱动8只LED，低电平点亮 74HC573输入接P0端口，输出接8只LED，P1.4控制LE 【实验步骤】 ISP下载开关扳到“10”，用Flash Magic软件下载程序文件“8-LED.hex”，运行。 【运行效果】
forlinx6410-led1
- 6410的led等的裸机程序程序，一直在玩裸机，所以共享出来-6410 led Procedure for bare-metal, etc., has been playing bare metal, so share it
control-led1-and-led2-of-msp-430
- 当sw1 和sw2 被触发时发出不同频率的LED灯闪烁- Initiates LED1 and LED2 to blink on and off at a set rate. * When SW1 is pressed, the frequency is toggled to double. * When SW1 is pressed again, the frequency is reset.
LED1
- 外部中断0控制LED1亮,按键ENT0灯LED1就亮，再按，就灭。-External Interrupt 0 Control LED1 bright, button ENT0 light LED1 on the light, then, went out.
timer-to-LED1
- 基于研旭DSP28335基础版编写的例程，通过定时器控制LED1的亮灭，定时时间可调-Based on research Asahi DSP28335 Basic routines written by timer control LED1 light off, adjustable timing
6.外部中断改变LED1状态实验
- 外部中断改变LED1状态实验，包含学习文档，适合初学者学习(External interrupts change the LED1 state experiment, including learning documents, suitable for beginners to learn)
64.光敏电阻模拟量输入控制LED1亮度变化
- 光敏电阻模拟量输入控制LED1亮度变化（TIM1定时器产生PWM波形）实验(Photosensitive resistor analog input control LED1 brightness change (TIM1 timer generates PWM waveform) experiment)