搜索资源列表
motodrive
- 基于labview的控制电机转动的程序,很有用的.是本人的毕业设计-LabVIEW-based control of motor rotation procedure, very useful. Is my graduation project
NI_motor_test
- 基于NI6221卡的电机测试控制程序，由NI6221卡发脉冲控制电机转速，再由6221卡读回电机的转速信号并显示-NI6221 card-based motor test control procedures, NI6221 card issued by the pulse control motor speed, and then from 6221 card read-back motor speed signal and disp
wp_lineardata
- 用Labview生成控制电机匀加速启动和匀减速停止的数据-Using Labview to generate electrical control to accelerate the start-up and absorbed absorbed deceleration stop data
labviewmoto
- 用labview编写的电机控制上位机软件,可以显示电机的当前速度和转速波形图,通过串口通讯-Prepared using LabVIEW motor control PC software, can display the motor speed and speed of the current waveform through the serial communication
Motor_speedup_speeddown
- 电机匀加速匀减速数据_频率给定与输出分析-Motor speed up and speed down with same acceleration analyse
LabVIEW_Fuzzy_Logic_control
- 基于LabVIEW的直流电机模糊控制系统设计-LabVIEW-based Fuzzy Control System Design of DC Motor
motorcontrol
- 电机启动控控制转速优化等功能-motor spin up control
LabVIEWMotion
- labview的电机控制的llb文件，在用labview控制电机时候很方便的-labview motor control of the llb file using labview to control motor is very convenient when
motor
- labview应用LABJACK的电机实验程序,便于初始都学习-labview motor applications LABJACK experimental procedure, to facilitate both the initial learning
zhiliudianji
- 利用实验仪上的D/A变换电路，输出-8V至+8V电压，控制直流电机。改变输出电压值，改变电机转速。用8051的定时器0生成单位时间，由定时器/计数器1对单位时间内的脉冲计数，计算电机转速。参考数码管实验，将电机的实际转速在数码管上显示出来。-Experimental apparatus on the D/A converter output voltage of-8V to+8 V, control DC motor. Change t
controlsteppermotor
- 用Labview编写的向单片机发送步进电机控制信号的界面-Prepared to use Labview to send stepper motor control signal microcontroller interface
BJKZ
- 使用NI-6008控制步进电机（方向，步进数可调）-Using the NI-6008 control stepper motor (direction, step a few adjustable)
LabVI
- LabVIEW航空发电机性能参数测试系统设计LabVIEW aviation turbine performance testing system-LabVIEW aviation turbine performance testing system
12
- LabVIEW_快速构建步进电机控制系统的利器-LabVIEW_ rapid construction of stepping motor control system etc
LabVIEW-PLC
- 基于LabVIEW平台和PLC的电机试验台数据采集系统设计-LabVIEW platform and PLC based motor test stand data acquisition system
dianjitiaosu
- 使用labview实现了各种电机变速方式下的信号波形变换过程 。-Achieved using a variety of labview motor speed mode signal waveform transformation process.
电机转速计算
- 采用labview编写的电机转速计算器，输入轮胎直径 、减速比、要求车速，输出所需电机转速(Written by LabVIEW motor speed calculator, enter the tire diameter, speed reduction ratio, speed requirements, the output motor speed required)
直流电机位置控制
- 直流电机位置控制，前面板设置电机指针位置，运行程序，电机即可按照预设值转动。(DC motor position control, the front panel set the motor pointer position, run the program, the motor can be rotated according to the preset value.)
步进电机控制
- 能够使用arduino uno r3来通过步进电机控制器，实现步进电机旋转角度及旋转速度的控制(Arduino uno R3 can be used to control the rotation angle and speed of stepping motor by stepping motor controller.)
电机演示vi
- Labview 做电机的上位机程序，包含串口通信协议， 电压，电流，转速测试等(this program is designed by labview 2012. It is used for BLDC control, voltage, current and rpm monitor.)