搜索资源列表
ADC3
- ADC的源程式，把51的正負極接至ADC，再將ADC.asm檔compile後，ACD便會產生將類比轉成數位訊號的效果-ADC source programs, and 51 are negative then to ADC, and then compile ADC.asm stalls, the ACD will have to switch analog signals into digital effects
ADC3
- ADC的源程式，把51的正負極接至ADC，再將ADC.asm檔compile後，ACD便會產生將類比轉成數位訊號的效果-ADC source programs, and 51 are negative then to ADC, and then compile ADC.asm stalls, the ACD will have to switch analog signals into digital effects
AVR_IMU_1
- 卡尔曼滤波在AVR单片机的应用，引脚接法：PC1 (ADC1) Y Accel (Pin 8) PC2 (ADC2) Z Accel (Pin 7) PC3 (ADC3) X Rate (Pin 3) PC4 (ADC4) Y Rate (Pin 4) PC5 (ADC5) VRef (Pin 5) - Currently, this project assumes the AVR ATmega168 M
ADC3
- STM32非固件库程序，实现功能：ADC3-Non-STM32 firmware library program, to achieve functional: ADC3
adc3
- take a input vector which is no of users of b[kx1] and code vector which will be a matrix now s=[Nxk],where then give to matched filter,non-correlating detector, by randomised sequence.-take a input vector whic
ADC591
- 51单片机AD转换应用，采样ADC3的模拟输入并把结果通过LED显示出来-51 MCU AD conversion applications, sampling ADC3 analog input and the results are displayed through LED
ADC3
- msp430单片机 ACD程序之三-The third ACD process msp430 microcontroller
AD_TEST
- 本文件是AD测试实验；测试前需要对管脚复用的电压基准进行设置，将JP10的2，3脚短接，1脚空出。AD输入端子(J10)可输入4路AD(ADC0--ADC3)，另有1路可测量片内温度，5路采样值都通过串口发送出去，在串口调试助手上看观察其值。4路AD中ADC0可通过跳线器(JP5)“ADJ_VOL”（1，2脚短接）与板上电位器相连，通过手动调VR1可以观察到电压值的变化-This document is the AD test expe
ADC3
- STM32 AD转换程序源代码 STM32 AD转换程序源代码-STM32 AD conversion source code STM32 AD conversion source code
C8051F320Software
- (1) AD_TEST: 摘 要： 本文件是AD测试实验；测试前需要对管脚复用的电压基准进行设置，将JP10的2，3脚短接，1脚空出。AD输入端子(J10)可输入4路AD(ADC0--ADC3)，另有1路可测量片内温度，5路采样值都通过串口发送出去，在串口调试助手上看观察其值。4路AD中ADC0可通过跳线器(JP5)“ADJ_VOL”（1，2脚短接）与板上电位器相连，通过手动调VR1可以观察到电压值的变化。-(1) AD_TEST
Adc3_dma
- This example describes how to use the ADC3 and DMA to transfer continuously converted data from ADC3 to memory. The ADC3 is configured to convert continuously channel7. Each time an end of conversion occurs the
adc3
- it is a adc12 design.it is my design.you can use it.
ADC3
- adc3,模拟数字装换程序，可用，已经实验验证-adc3, analog-to-digital installed for the program can be used, has been experimental verification
ADC3_DMA
- This example describes how to use the ADC3 and DMA to transfer continuously converted data from ADC3 to memory. The ADC3 is configured to convert continuously channel7. Each time an end of conversion occurs the DM
USE_STDPERIPH_DRIVER-STM32F30X-
- 基于stm32f303v的方波逆变器，调用外设adc1，adc2，adc3，定时器1和定时器3做PID控制-Based on the square wave inverter stm32f303v, call peripherals adc1, adc2 and adc3, timer timer 1 and 3 do PID control
stm32f746_ADC
- 本例介绍如何使用ADC3和DMA，从ADC3到存储器不断传输转换后的数据。 该ADC3配置为连续转换ADC_CHANNEL_8。 每次转换结束时的DMA传输，在循环模式下， 从ADC3 DR转换后的数据注册到uhADCxConvertedValue变量。 该uhADCxConvertedValue读值编码为12位，VREF +基准电压连接 在董事会到VDD（+ 3.3V）时，Vref-之间的参考电压
STM32F746-ADC
- 这个是STM32F746源碼演示了如何使用ADC3及DMA传输连续 转换后的数据从ADC3记忆。 ADC3的配置不断转换的adc_channel_8。 每次转换结束时，DMA传输，循环模式，这 转换数据寄存器变量的uhadcxconvertedvalue ADC3博士。 的uhadcxconvertedvalue读取的值是12位编码，参考电压VREF +连接 在VDD的板（+3.3V），VREF参考电压连接板上到
ADC3andDMAhighspeed(2.4Msps)
- 硬件平台：STM32F429I-DISCORVERY 软件平台：KEIL MDK5.10 在STM32F429I-DISCO board中，由于串口2被L3GD20和液晶数据线占用，所以串口1很方便，而且还留了2个孔外接。 * 说 明 : 实现printf和scanf函数重定向到串口1，即支持printf信息到USART1 * 实现重定向，只需要添加2个函数: * int fputc(int ch,
ADC3
- msp430f149 adc测试代码和CC110通讯-msp430f149 adc test code communications and CC110
timer+ADC+DMA
- 基于STM32F407的程序，实现了通过DMA方式进行ADC采样，并通过定时器定是触发。程序中使用了ADC3-channel0,1,2;通过定时器2触发。程序已在STM32F407开发板上验证。(Based on the STM32F407 program, to achieve the ADC sampling through the DMA, and through the timer is triggered. ADC3-chan