搜索资源列表
fet440_uart11_38400
- MSP430F449 子程序,MSP-FET430P440 Demo - USART1 UART 38400 Echo ISR, DCO SMCLK.-MSP430F449 subroutine, MSP-FET430P440 Demo-USART1 UART 38400 Echo IS R, the making of SMCLK.
fet440_wdt01
- MSP-FET430P440 Demo - WDT Toggle P5.1 Interval overflow ISR, DCO SMCLK-MSP-FET430P440 Demo - 14d Toggle P5.1 Inte rval overflow ISR, the making of SMCLK
fet440_bt01
- MSP-FET430P440 Demo - BasicTimer Toggle P5.1 using ISR, DCO SMCLK-MSP-FET430P440 Demo-P BasicTimer Toggle 5.1 using ISR, the making of SMCLK
fet440_bt02
- MSP-FET430P440 Demo - BasicTimer Toggle P5.1 using ISR, 32kHz SMCLK -MSP-FET430P440 Demo-P BasicTimer Toggle 5.1 using ISR, 32kHz SMCLK
fet440_ta_pwm01
- MSP-FET430P440 Demo - Timer_A PWM TA1-2 upmode, DCO SMCLK-MSP-FET430P440 Demo-Timer_A PWM TA1-2 up mode, the making of SMCLK
fet140_clks
- MSP-FET430P140 Demo - Basic Clock, Output Buffered SMCLK, ACLK and MCLK
fet140_tb_09
- MSP-FET430P140 Demo - Timer_B, PWM TB1-2, Up/Down Mode, DCO SMCLK-MSP-FET430P140 Demo-Timer_B, PWM TB1-2. Up / Down Mode, the making of SMCLK
msp430x1xx_fet_1
- //*** *** *** *** *** *** *** // MSP430x1xx Demo - Software Toggle P1.0 // // Descr iption Toggle P1.0 by xor ing P1.0 inside of a software loop. // ACLK = n/a, MCLK = SMCLK = default DCO // // MSP430x1xx
fet110_1
- //*** *** *** *** *** *** *** * // MSP-FET430x110 Demo - Software Toggle P1.0 // // Descr iption: Toggle P1.0 by xor ing P1.0 inside of a software loop. // ACLK = n/a, MCLK = SMCLK = default DCO ~800k // // M
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, e
fet120_clks
- MSP-FET430P120 Demo - Basic Clock, Output Buffered SMCLK, ACLK and MCLK/10
fet410_ta
- MSP-FET430P410 Demo - Timer_A Toggle P5.1, CCR0 Contmode ISR, DCO SMCLK Descr iption Toggle P5.1 using using software and TA_0 ISR. Toggle rate is set at 50000 DCO/SMCLK cycles. Default DCO frequency used for TAC
d169_dma
- D169 Demo - DMA0 Repeated Burst to-from RAM, Software Trigger Descr iption A 32 byte block from 220h-240h is transfered to 240h-260h using DMA0 in a burst block using software DMAREQ trigger. After each transfer
fet140_spi
- MSP-FET430P140 Demo - USART0, SPI Interface to HC165/164 Shift Registers Descr iption: Demonstrate USART0 in two-way SPI mode. Data are read from an HC165, and same data written back to the HC164. ACLK = n/a MCL
msp430x11x1_549
- 宣读了一份tlc549 ADC的参考vcc使用软件SPI和存储8位数字代码在adcdata 。该tlc549采样，在一个连续循环。如果adcdata > 0.5 * vcc ， p1.0设置，否则复位。aclk为N /甲mclk = smclk =预设会计处〜 800k vcc必须至少为3V为tlc549
USART_ADC12
- MSP430F149串口行实验程序 //使用ADC12采集实验,将采集到数据送向PC.(序列单次采集,采用定时器A作为时钟源) //P3.4为发送,P3.5为接收 晶体使32768HZ/8MHZ. 串行波特率B/S //使用SMCLK作为波特率发器时,不能使用LPM2,LPM3!
fet440_uart11_38400
- Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK
红外接收
- 430红外接收 #include #include #include #include #include "xtype.h" #define IRDA (uint8)0x01 //P1_0 uint8 ifg; uint8 index=0,value; uint8 bitValue; ui
fet440_uart11_38400
- MSP430F449 子程序,MSP-FET430P440 Demo - USART1 UART 38400 Echo ISR, DCO SMCLK.-MSP430F449 subroutine, MSP-FET430P440 Demo-USART1 UART 38400 Echo IS R, the making of SMCLK.
fet440_wdt01
- MSP-FET430P440 Demo - WDT Toggle P5.1 Interval overflow ISR, DCO SMCLK-MSP-FET430P440 Demo- 14d Toggle P5.1 Inte rval overflow ISR, the making of SMCLK