搜索资源列表
MSP430单片机与L298驱动控制单片机正反转直行后退
- MSP430单片机与L298驱动控制单片机正反转直行后退 基于IAR for MSP430F16X
moto_PWM
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical c
20080228015123_200822716251417026
- 使用定时器产生PWM波，可配合L298N用来驱动普通直流电机。适用于51单片机-use PWM timer generated wave, and with the drive for general L298N -PWM wave generated using the timer, it can tie in L298N common DC motor used to drive. Applied to 51 single-chip
motor2
- 电机驱动，用单片机加L298实现直流电机的驱动，能够控制转速、方向等-Motor drive with single-chip plus realize L298 DC motor driver, to control speed and direction
L298
- 双直流电动机驱动集成电路，能控制直流电动机的正、反转及制动，驱动能力强，外围电路简单。-Dual DC motor driver integrated circuits, can be controlled by DC motor is, reverse and brake, driving ability, a simple peripheral circuits.
pwm
- 利用延时产生pwm信号，通过L298功率放大器驱动直流电机- pwm DC-motor
MOTOR
- msp430控制直流电机，L298驱动，具有正反转，pwm调速功能。-msp430 control of DC motor, L298-driven, with positive inversion, pwm speed control function.
PWMControlMOTOR
- 多功能小车仿真。L298驱动直流电机，有液晶LCD显示方向，速度。-Multi-function car simulation. L298-driven DC motor,there is the direction of liquid crystal LCD display,speed.
L298
- L298驱动直流、步进电机，带有PROTUES仿真-L298-driven DC, stepper motors, with PROTUES simulation
12
- 超声波测距 原创 c编写 1602显示 温度 补偿 按键测距 -c lcd1602
L298
- 基于ARM7的L298驱动程序，芯片L298，控制两个直流电机，没有用PWM调速-Based on ARM7-L298 driver chip L298, control two DC motors, there is no speed control with PWM
1
- 这是一个使用51单片机加上L298驱动直流电机的程序源代码。-This is a single chip using 51 L298-driven DC motor with source code.
DC-motor-driver-program-of-L298
- L298驱动直流电机程序,其中包括正反转-L298 DC Motor Driver Program
motor02
- 自己写的电机控制第二个:VB做的上位机通过串口向51单片机发送命定，通过L298驱动直流电机，电机反溃的信息又发回VB到VB上显示-To write the second motor control: VB to do the PC via the serial port to send commands to the microcontroller 51 set by L298 drive DC motor anti-ulcer in
L298
- 仅仅使用L298驱动芯片，主控为51单片机，在keil中调试测过，专门驱动步进电机的！不是直流电机。-Just use the L298 driver chip, the master microcontroller 51, in keil debugging measured before, specifically to drive stepper motor! Not a DC motor.
zhiliudianji
- 运用L298驱动直流电机，代码中包含有正转、反转、停止等程序。-DC motor driver using L298, the code contains a forward, reverse, stop and other procedures.
DC-Motor
- 基于stm32的L298驱动直流电机调速程序-Based on the L298 stm32 drive DC motor speed control program
L298
- L298控制直流电机，C语言驱动，可直接用于凌阳单片机，亦可改动接口后用于其他单片机-L298 controlled DC motor, C language driver, can be used directly Sunplus can also be used for other changes to the interface chip after
l298
- AT89S52单片机，L298驱动直流电机C51程序-l298-driven DC motor
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得，通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差，经过控制算法得出控制量。单片机再把控制量以PWM的形式输出，经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速，并让用户通过键盘输入设定速度。(The motor speed feedback signal measured