搜索资源列表
s3c2410,iar
- s3c2410 ads下的测试程序移植到 iar ewarm v5.2；包括 Please select function : 0 : Please input 1-14 to select test 1 : Real time clock display 2 : 4 key array test 3 : Buzzer test 4 : ADC test 5 : IIC EEPROM test 6 : Touchpanel test 7
Micrium-NXP-uCOS-II-LPC2106
- LPC2106开发板上面的uCOS移植代码最新版2.83，基于IAR编译系统-LPC2106 development board for uCOS transplant above code the latest version 2.83. Based on the IAR Compiler System
M128_IAR_UCOSII
- Atmega128高档8位单片机的uCOSII移植源码工程文件，uCOSII的版本是v2.83，工程文件包括了IAR和ICC两个编译器。-Atmega128 high eight SCM uCOSII transplant source project documents, uCOSII version is v2.83, the document includes the ICC and the two IAR compiler.
PC-lint_8.00x
- pclint 8.00x。C/C++软件代码静态分析工具PC-Lint的最新版8.00x，内涵PC-Lint集成到VC++6.0和SourceInsight的方法和步骤。强烈推荐大家使用。-pclint 8.00x. C/C++ software code static analysis tool for PC-Lint the latest version of 8.00x, the connotation of PC-Lint in
mb1504_TEST_MSP430
- 运用MSP430驱动锁相环MB1504的程序，IAR编译。能够实现8—60Mhz频率范围精确锁定，步进为10khz-Use MSP430-driven PLL MB1504 procedures, IAR compiler. Be able to achieve 8-60Mhz frequency range precision locking, stepping to 10kHz
lpc22xxIARuCOS2.8
- iar编译环境下移植ucos 2.86到lpc22xx系列mcu源码。-replant ucos 2.86 for lpc22xx mcu in iar compile environment.
ST7528
- JCG160100A02-01驱动程序,适用于ST7528控制器(8-bit & 8080-series parallel ) IAR开发-JCG160100A02-01 driver for ST7528 controller (8-bit & 8080-series parallel)
project_bell_2
- This file is code in IAR EWAVR and Proteus files an project bell2 .MCPU is Atmega 8 .Realised SPI and I2C programm procedures .-This file is code in IAR EWAVR and Proteus files an project bell2 .MCPU is Atmega 8 .Realis
lab4.1
- ARM7驱动，开发环境IAR，板子用的是YL-LPC2148。 驱动并测试LCD显示屏， 控制LCD以5×8点阵滚动显示字符串：“Test one”,“Test two”。-ARM7 driven development environment, IAR, board with the YL-LPC2148. LCD display driver and test, control, 5 × 8 dot matrix LCD to sc
iar
- 从左到右的流水灯：接在P0口的8个LED从左到右循环依次点亮，产生走马灯效果 -Light water from left to right: P0 port connected to the 8 LED lights turn from left to right cycle, resulting in a revolving door effect
3.8.2_time_16_count
- 流明ARM开发板设置定时器示例程序，可以直接在IAR编译器上运行使用。-Lumens ARM development board set the timer example program, can direct IAR compilers run use.
jvyuwxins
- IAR AVR5.50 CRACK FILES,IAR AVR CRAC K FILES-IAR AVR5.50 CRACK FILES,IAR AVR CRACK FILES,IAR AVR CRACK FILES
backup2012-8-31
- 开发环境为IAR，基于MSP430实现的一个小型传感网络，例子里有两个文件夹，一个GW：表示网关，一个point:表示传感器节点；传感器节点可以通过传感器采集数据，通过CC1000无线发射给网关，网关接收数据并处理后通过串口传给PC，PC端程序未给出，由另外一个同学负责。-Development environment IAR, based on the MSP430 a small sensor network, example, t
qpy800600-1616-c-iar
- 能完成8060液晶屏的显示功能，掌握该程序能快速使用液晶屏的控制，QPY系列8为接口8位色屏，使用STC11L60XE单片机驱动，外部晶振12M.驱动电压5V，编译环境：keil uvision4 该函数主要实现：单点/8点清屏、读写显存、亮度调节、写边框、填充色块、写数字、刷新显示等测试 -Complete 8060 LCD display function, to master the program quickly using t
8-1
- msp430,FLASH擦写程序,IAR,可以直接使用-msp430, FLASH erase procedure, IAR, can be used directly
8--8-Light-Cube
- 8*8光立方，使用msp430g2553单片机，变成环境为IAR。-8* 8 light cube, using msp430g2553 microcontroller into the environment IAR.
IAR+STM8L151_CodePrj_20171104
- IAR+STM8L151工程模板代码： 1、在IAR中建立STM8工程步骤详细说明，详见压缩包文档《在IAR中建立STM8工程步骤2017-8-10 163427.docx》； 2、重定向printf()gechar()到USART3； 3、采用STM8L151标准库文件V1.6.1。(IAR+STM8L151 engineering code: 1, the establishment of STM8 engineering step
开发环境IAR EW8051-8.1带注册工具
- 开发环境IAR EW8051-8.1带注册工具(IAR EW8051-8.1 very good)
IAR-8.10.1
- 单片机开发工具，一个是安装软件，一个是序列号产生器。(RELEASE NOTES for IAR Embedded Workbench for 8051 version 8.10.1 Read about the latest features, new device support, and program corrections in the release notes. Highlights Important inf
编译器配置文件V1.8 IARVer
- HT系列单片机的IAR工程配置文件，覆盖相应目录即可，增加了IAR对HT系列单片机的支持(HT Microchip IAR configuartion file, overwrite relative directory, support HT series)