搜索资源列表
RELAY 2 继电器
- 继电器
两继电器间隔推迟关断
- 单片机控制继电器的开断，延时时间导通和关断。(The single chip microcomputer controls the interruption of the relay, the time delay, the turn-on and the turn off.)
基于51光敏电阻控制继电器
- 基于51单片机，当光敏数值小于20时，继电器1和2工作，当数值小于10时继电器3延时5秒工作，当数值大于50时继电器全部断开。（数值参数和延时数值可更改，继电器可加减）(Based on 51 single-chip microcomputer, when the light sensitive value is less than 20, the relay 1 and 2 work, when the value is less t
4、继电器
- 此为单片机中的继电器程序，仅供给初学者学习和使用(This is the microcontroller in the relay program, only for beginners to learn and use)
097、用红外遥控器控制继电器
- 用51单片机控制红外遥控器，从而控制继电器的运行状态(The infrared remote controller is controlled by 51 single chip microcomputer, so as to control the running state of the rela)
18. 继电器控制照明设备
- 51单片机的继电器控制照明设备，带有proteus 仿真，简单方便(51 single chip relay control lighting equipment)
按键控制继电器通断
- 利用c语言程序实现按键控制继电器通断的程序代码(The use of C language program to achieve the button control relay off the program code)
90-继电器控制原理
- 90-继电器控制原理(Control principle of 90- relay)
91-双继电器模拟洗衣机电机控制
- 91-双继电器模拟洗衣机电机控制(91- double relay simulation motor control of washing machine)
4、继电器
- 51上的继电器设计，简洁干净，适合开发新的开发板(51, the relay design, simple and clean, suitable for the development of new development board)
Li_继电器测试
- 易语言写的一个测试串口通讯控制5路继电器模块的源码(Use E language to write a test serial communication control, 5 relay module source code)
02.继电器控制
- 继电器的控制，初学者可以参考。平台给予STM8写的，继电器可以吧若ID个按控制转换成强电控制(Relay control, beginners can refer to. The platform is written in STM8, the relay can be, if ID, according to the control into strong electricity control)
实验5：继电器
- 51开发板中第5个程序继电器，运行程序后会自动打开继电器(The fifth program relay in the development board, which automatically opens the relay after running the program)
单片机汇编：继电器
- 实验：按键控制继电器。 现象：按下K1键继电器闭合，LED发光(Assembly program of key control relay.)
实验5：继电器
- 这是单片机的继电器程序代码。用proteus仿真实验特别基础。(This is the single - chip relay program code.Using proteus simulation experiment special basis.)
11.按键无线控制台灯和LED灯 继电器
- 在zigbee协议栈中 按键无线控制台灯和LED灯 继电器(Key wireless control desk lamp and LED lamp relay in ZigBee stack)
1路带光耦继电器模块
- 单路继电器模块：可设置高或低电平驱动；继电器电压可设定；(Single circuit relay module: high or low level driver can be set up.)
011、UART串口发送字符控制继电器开关
- stc15f104 UART串口发送字符控制继电器开关(Stc15f104 UART serial port to send character control relay switch)
012、UART串口发送十六进制控制继电器开关
- stc15f104 UART串口发送十六进制控制继电器开关(Stc15f104 UART serial port sends sixteen control relay switch)
继电器控制
- 用8031单片机和8255控制继电器，实现外部电路转换。按一个按钮，第一条线通，再按一下，第一条线路断开，第二条线路通。(The external circuit conversion is realized by using 8031 single chip and 8255 control relay. Press one button, the first line is connected, and then press, th