搜索资源列表
数字电位器原理与单片机的接口设计
- 数字电位器原理与单片机的接口设计--电子书籍。可以一看。或许对你有用-Digital Potentiometers Principle and microcontroller interface design -- electronic books. One can see. May be useful to you
改变数字电位器模块
- 使用C语言编写的改变数字电位器的程序，开发环境为KEIL，试验成功，与大家分享一下-use C language changes Digital Potentiometers procedures for KEIL development environment, the tests are successful, share with you
51单片机何控制x9c104p数字电位器
- 51单片机何控制x9c104p数字电位器
51单片机何控制x9c104p数字电位器
- 51单片机何控制x9c104p数字电位器
数字电位器原理与单片机的接口设计
- 数字电位器原理与单片机的接口设计--电子书籍。可以一看。或许对你有用-Digital Potentiometers Principle and microcontroller interface design-- electronic books. One can see. May be useful to you
改变数字电位器模块
- 使用C语言编写的改变数字电位器的程序，开发环境为KEIL，试验成功，与大家分享一下-use C language changes Digital Potentiometers procedures for KEIL development environment, the tests are successful, share with you
X9241
- 数字电位器X9241与PIC单片机的接口及程序设计-Digital Potentiometers X9241 and PIC microcontroller interface and the program design
zhengxianxinhaofashengqi
- 本系统基于直接数字频率合成技术；以凌阳SPCE061A单片机为控制核心；采用宽带运放AD811和AGC技术使得50Ω负载上峰值达到6V±1V；由模拟乘法器AD835产生调幅信号；由数控电位器程控调制度；通过单片机改变频率字实现调频信号，最大频偏可控；通过模拟开关产生ASK、PSK信号。系统的频率范围在100Hz～12MHz,稳定度优于10-5，最小步进为10Hz-The system is based on Direct Digital
PT2259_s_1
- 数字电位器，用数字电位器替代机，\用数字电位器替代机械式电位器-Digital Potentiometers, Digital Potentiometers alternative aircraft, \ Digital Potentiometers replace mechanical potentiometers
brpinfo
- 用数字电位器替代机械式电位器WOSDOFEODF-Digital Potentiometers replace mechanical potentiometers WOSDOFEODF
plussw
- 编码电位器原代码,测试过!网上很少有这个资料,这个程序有消抖功能-coding potential for the original code, test it! Few of the online information, the procedure to get a source function
CS3310
- 本文件的源代码:高保真数控电位器CS3310的驱动.-this document the source code : high fidelity NC Potentiometers CS3310-driven.
disp_0123.CPP
- 这是我编写的电子电位器C程序 网对学习单片机的朋友有帮助-This is what I prepared for the potential of electronic networks C program of study SCM help a friend
AD8402
- 数字电位器AD8402驱动程序， AD8402驱动程序-Digital Potentiometers AD8402 driver, AD8402 driver, AD8402 driver
x9318
- 数字电位器x9318中文使用说明以及控制程序.asm-Digital Potentiometers x9318 Chinese use and control procedures. Asm2
mpr
- 用C8051F300实现的电动机保护继电器,通过电位器调节整定电流和启动延时时间.-C8051F300 realize with the motor protection relay, through the adjustment potentiometer setting current and start-up delay time.
数字电位器控制编程
- 单片机控制数字电位器x9313的编程。本编程结合运算放大器设置成一个可调电源，通过单片机控制电位器的阻值修改电位器两端电压从而达到数控电源的效果。电压值可通过单片机外界LCD显示。(Programming of digital potentiometer X9313 controlled by mcu. This program is combined with operational amplifier set into an adj
X9C103数字电位器程序
- X9C103数字电位器程序 1111111111(X9C103 digital potentiometer program)
模拟spi控制数字电位器
- 利用单片机通过模拟SPI线控数字电位器，使数字电位器输出想要的电阻值。(Using MCU to simulate SPI wire controlled digital potentiometer)
通道2测量电位器
- 使用tlc1543，构成测量电位器，相关电路连接及编程测试。(Use TLC1543 to form measuring potentiometer, relevant circuit connection and programming test.)