搜索资源列表
NB358
- PIC烟雾报警器例程，仅供相关人员参考。 PIC烟雾报警器例程，仅供相关人员参考。-PIC smoke alarm routines, the only relevant reference. PIC smoke alarm routines, the only relevant reference.
NB358
- PIC烟雾报警器例程，仅供相关人员参考。 PIC烟雾报警器例程，仅供相关人员参考。-PIC smoke alarm routines, the only relevant reference. PIC smoke alarm routines, the only relevant reference.
FEII
- 烟雾报警器源程序,可以检测到无烟时不退出报警。-Smoke alarm source, can be detected when the smoke alarm does not exit.
rok282
- 超灵敏度的感灰烟型烟雾报警器，实用于家庭使用。-Misty-type ultra-sensitive smoke alarms sense, practical for home use.
smoke-alarm
- 烟雾报警器的功能设计，内含AD0809取样，C51处理和数码管输出源码-The functional design of the smoke alarm, containing AD0809 sampling C51 processing and digital tube output code
SMOKE_test
- CC2540烟雾报警器模块测试程序 烟雾报警器，检测到烟雾时，GPIO输出高电平，报警消失后，变低电平-CC2540 module test procedures smoke alarm smoke alarm, when smoke is detected, GPIO output high, the alarm disappears, goes low
CC2530smoke-alarm
- CC2530 烟雾报警器。一个简单的例程-CC2530 smoke alarm.
stc51-smoke-alarm
- 基于STC51系列单片机的烟雾报警器，实现了完整功能并通过编译-Based STC51 Series MCU smoke alarms, to achieve a fully functional and compile
Smoke-alarm
- 基于DS18B20和MQ-2的温度烟雾报警器-Smoke alarm。DS18B20
8-bit-mcu-application-example
- 基于8—bit单片机的抢答器、烟雾报警器应用实例，-8-bit mcu application example
yanwubaojing
- 设计以烟雾报警器，可以移植为酒精等类似气体浓度监测，超过设定浓度，可以通过继电器驱动风扇-Designed to smoke alarms, portable gas concentration monitoring similar to alcohol, the concentration exceeds a set, you can drive the fan relay
ywbj
- 自制的烟雾报警器的源码，所使用的原理是检测光敏接收管的AD值，根据AD值来判断是否报警。-The smoke alarm homemade source, principle is used to detect a photosensitive receiving tube AD value, according to the AD value to determine whether the alarm.
chengxu
- MQ-2烟雾报警器的使用程序。并不复杂，适合初学者。-The use of MQ- 2 smoke alarm program.Is not complicated, suitable for beginners.
smoke-alarms
- 基于单片机的烟雾报警器，完整的实验报告，有c语言程序，有proteus图-Microcontroller-based smoke alarm, a complete test report, there is c language program, there proteus diagram
yawu
- 利用mq-2烟雾传感器，单片机制作烟雾报警器，并在12864显示，蜂鸣器报警-Use mq-2 smoke sensor, MCU production smoke alarm and 12864 show buzzer alarm
Smoke-detection-system
- 本文所设计的智能家居烟雾报警器采用单片机AT89C51，其价格便宜且性能稳定。本设计能将处于测试环境中的烟雾传感器输出的模拟电压通过A/D转换器送入单片机中进行处理并通过数码管显示，通过预设报警值，当检测到的烟雾浓度达到或者超过设定值时，用单片机控制发光二极管发光报警，同时喇叭工作发出声音报警，来达到监控的目的，以防事故的发生。-In this paper, the design of smart home smoke alarm us
11
- CC2530芯片的使用和无线传感器网络的构建——CC2530控制灯光强弱、步进电机、烟雾报警器程序-The use of CC2530 chip and the construction of wireless sensor network
EZRadioPRO_REVC2
- 详细说明烟雾报警器与智能家居的之间的发展(Explain the development of smoke alarms and smart home)
TEST _MQ2
- 测量MQ2烟雾传感器的数据并进行处理 可以进行AD转换(The data of the MQ2 smoke sensor is measured and processed to make AD conversion)
szw
- 声光报警、显示楼层、oled1602、7段显示数码管(Acousto-optic alarm, display floor, OLED 1602, 7 segment display digital tube)