搜索资源列表
LED
- 本程序为再单片机开发平台下用汇编语言编写的流水灯程序，可以用单键实现LED的灯花样闪烁。-This procedure for the re-development platform for single-chip using assembly language procedures prepared water lights can be used to realize one-touch LED lights blinking pa
deng
- 单片机流水灯程序，可以实现8个LED来回流动闪烁。-flow light
Multistatewaterlights
- 多种状态的流水灯课程设计:LED闪烁种类： ①、单个LED顺时针闪烁 ②、LED顺时针递增亮 ③、红灯LED和绿灯LED两者循环交替闪烁 ④、对角线LED顺时针循环闪烁 ⑤、所有LED同时闪烁 ⑥、单个LED顺时针闪烁，再逆时针闪烁 ⑦、对角线LDE顺时针闪烁，再逆时针闪烁 ⑧、LED顺时针递增亮，再逆时针递增亮 ⑨、两个LED顺时针闪烁 -Multi-state water lights
horse_light4
- 六种花样的流水灯，从左至右，从右至左，中间向两边，两边向中间，跳格闪烁等。verilog语言编写； 并且扩展容易； 有两个状态机构成实现。quartus 9.0和7.1仿真通过。无错误，无警告。-Six kinds of patterns of flowing water lights, from left to right, from right to left, in the middle to both sides, bo
STC-51-ASM
- 单片机流水灯程序，实现四个流水灯的轮流闪烁-SCM water light program, realization of the four water lights flashing
gpio
- 基于DSP2812，使用GPIO的引脚来控制LED灯闪烁。即控制XF引脚高低电平不断变化。(Based on the DSP2812, the GPIO pin is used to control the LED flashes. The XF pin is constantly changing between high and low levels.)
心形花样灯 程序
- 基于51单片机的心形流水灯程序,程序中包含各种花式闪烁(Based on 51 SCM heart-shaped water lamp program)
5-野火M3-流水灯
- 流水灯 基于野火开发板 板载的LED1、LED2、LED3以一定的频率闪烁。(Running light The onboard LED1, LED2, and LED3 flashes at a certain frequency.)
5-野火M3-流水灯
- 基本的stm32入门程序，控制led灯的闪烁与熄灭(Basic STM32 entry procedures, control LED lights flashing and extinguished)
实验3：LED流水灯
- 用C51单片机进行流水灯控制，每秒闪烁一次(C51 microcontroller with water light control, flashing every second)
1、（通用IO口方式）实现LED灯全亮全灭闪烁
- 通用I/o口控制 led流水灯闪烁 全亮全灭(General I/o port control LED water lamp flashing full bright full kill)
sys
- 实现流水灯的闪烁控制，左右闪烁，来回，可控制时长(Realize the flashing control of water lampRealize the flashing control of the water lamp, realize the flashing control of the water lamp, flicker left and right, back and forth, can control the l
LED闪烁
- 89C51单片机的流水灯教程通过编程手把手教育初学者了解编写单片机程序(89C51 microcontroller of water light tutorial, through programming hands to educate beginners to understand the preparation of SCM program)
实验3：LED流水灯
- 51开发板中第3个程序循环流水灯，运行程序后会自动点亮所有小灯并闪烁(The 3rd program in the development board is circulating the running water lamp, which will automatically light all the small lights and blink when the program is running)
001 流水灯
- 流水灯实现灯的轮流闪烁，文件含有程序代码以及原理图(liushuidengasdadsdfcs)
心形流水灯
- 心形流水灯，采用32个LED发光小灯，单片机所有的IO口都使用上了，编程四种闪烁方式，循环亮起。(Heart - shaped water lamp, using 32 led small lights, SCM all io ports are used, programming four flashing way, cycle on)
流水灯
- 通过51单片机控制LED流水灯循环往复闪烁(Control LED flow lamp by 51 Singlechip)
02.LED闪烁
- 流水灯小程序,可以自定义输出接口，控制LED的亮灭(LED,int ledPin = 10;void setup() {pinMode(ledPin, OUTPUT);)
定时器实现流水灯
- 实现STM32基于定时器流水灯功能，通过定时器TIM1控制实现，三个流水灯交替闪烁(Realization of STM32 Based on Timer Pipeline Lamp Function)
流水灯高低4位交替闪烁定时器控制
- 定时器控制流水灯高低4位交替闪烁 中断方式T0模式2，内有Keil C源文件，已编译通过；内有Proteus仿真文件(DSN)，已仿真通过。(Timer control flow light high and low 4-bit alternate flashing interrupt mode t0 mode 2, with keil c source file inside, compiled; proteus simulation