资源列表
[matlab例程] asd
说明:基本思路:把各条弧上单位流量的费用看成某种长度,用Floyd求最短路的方法确定一条 % 自V1至Vn的最短路 再将这条最短路作为可扩充路,用求解最大流问题的方法将其上的流 % 量增至最大可能值 而这条最短路上的流量增加后,其上各条弧的单位流量的费用要重新 % 确定,如此多次迭代,最终得到最小费用最大流.-Basic ideas: to each arc on the unit cost of traffic as some length<xuechaoling> 在 2025-02-13 上传 | 大小:2kb | 下载:0
[matlab例程] FuzzyClusteringToolbox
说明:程序包包含的验证方法,会根据以下的多个指数分配系数(Partition Coefficient),分类熵Classification Entropy ,分区索引,分离指数(Separation Index),Xie and Beni s的索引,严重聚类的算法-Package contains the authentication method will be based on the following number of index<xuechaoling> 在 2025-02-13 上传 | 大小:1.97mb | 下载:0
[matlab例程] Newton-raphsom
说明:这个m文件实现了Newton raphsom算法,从而解决分布式功率流问题。-M realized this document Newton raphsom algorithm, so as to solve the problem of distributed power flow.<xuechaoling> 在 2025-02-13 上传 | 大小:2kb | 下载:0
[matlab例程] MATLAB_Financial_Toolbox
说明:Matlab Financial Toolbox<yang> 在 2025-02-13 上传 | 大小:5kb | 下载:0
[matlab例程] yangzhijie1488
说明:Matlab生成UG凸轮曲线 本人原创。我任务就凭这一个课件,我就能成为会员,呵呵。-Matlab generate original UG I cam curve. My task in itself was a courseware, I will be able to become a member, huh, huh.<杨志杰> 在 2025-02-13 上传 | 大小:167kb | 下载:0
[matlab例程] CDMA_MODULATION_DEMODULATION
说明:复接入,B/W双用户使用直接扩频序列 % >>>multiple access b/w 2 users using DS CDMA % >>>format is : cdmamodem(user1,user2,snr_in_dbs) % >>>user1 and user2 are vectors and they should be of equal length<hws> 在 2025-02-13 上传 | 大小:2kb | 下载:0
[matlab例程] BPSK_Sim_With_Binary_and_AskModul
说明:带有原二进制信号与BPSK调制后的信号图对比的BPSK仿真程序-With the original binary signal and BPSK modulation signal comparison of BPSK simulation program<hws> 在 2025-02-13 上传 | 大小:1kb | 下载:0
[matlab例程] acvancedPIDcontrol
说明:这是先进PID控制书中的源码,是基于matlab的。-This is the advanced PID control of the source book is based on the matlab.<唐新星> 在 2025-02-13 上传 | 大小:206kb | 下载:0
[matlab例程] matlabformimo2x2
说明:mimo2x2天线选择系统的全系统matlab程序,先前的是dsp程序.-Antenna Selection mimo2x2 system matlab system-wide procedures, the previous procedure is dsp.<chenfei> 在 2025-02-13 上传 | 大小:143kb | 下载:0