资源列表

« 1 2 ... .27 .28 .29 .30 .31 832.33 .34 .35 .36 .37 ... 842 »

[绘图程序XHTH

说明:原创源码-lisp-循环替换,批量对序号加减某一数值,适用于所有版本CAD-Original source-lisp- cycle replacement batch number addition and subtraction on a certain value, applies to all versions of CAD
<peace> 在 2025-04-28 上传 | 大小:4kb | 下载:1

[绘图程序three-dimensional-beam-pattern

说明:该代码描绘了线性声源和圆形活塞声源的三维波束图。-The source code depicts the linear and circular piston source of three-dimensional beam pattern.
<薛欢欢> 在 2025-04-28 上传 | 大小:2kb | 下载:1

[绘图程序plotleaf

说明:使用一篇论文提供的方程组和参数——分形仿射变换方法转换过来的MATLAB程序,画一片蕨叶。输入是起始坐标x0,y0和迭代次数——一般在几万次,十万次比较清晰。-Plotting the leaf with equations and parameters given by an essay. This method is fractal theory. The input is the location of starting poi
<ZHY> 在 2025-04-28 上传 | 大小:147kb | 下载:1

[绘图程序viewbasedata4

说明:该代码用于读取雷达数据,绘出雷达图形,用于诊断天气过程-the function of the code is to read the radar data
<达选芳> 在 2025-04-28 上传 | 大小:1kb | 下载:1

[绘图程序The-VB-curve-of-Apisoft-

说明:VB制件曲线图形的专用控件程序,使用现有控件方便实现图形-The VB curve of Apisoft 6
<郑学飞> 在 2025-04-28 上传 | 大小:1.73mb | 下载:1

[绘图程序chengxu

说明:用于画分布式电源输出容量与电流保护整定值之间关系图像。-Used to draw the distributed power output capacity and current protection setting values the relationship between image.
<李强> 在 2025-04-28 上传 | 大小:1kb | 下载:1

[绘图程序Automatic-drawing-Channel-Profile

说明:自动绘制渠道纵断面,可以根据在excel中编排好的里程高程数据好、快速绘制纵断面-Automatic drawing channel profile, according to the arrangement in excel good mileage elevation data is good, fast draw profile
<姚成> 在 2025-04-28 上传 | 大小:24kb | 下载:1

[绘图程序GB-SAR

说明:地基SAR基于两个点的形变检测,通过RD算法进行方位向压缩和距离向压缩,得到两幅图片,然后将这两幅图进行相位干涉得到形变量-SAR ground deformation detection based on two points, through RD algorithm azimuth compression and range compression to obtain two images, then these two figu
<fangzhiping> 在 2025-04-28 上传 | 大小:600kb | 下载:1

[绘图程序CstrBifurDAmFf

说明:单个化工过程CSTR反应器模型的非线性分岔图的作图程序。-A single CSTR reactor model of chemical process of nonlinear bifurcation diagram drawing program.
<lily> 在 2025-04-28 上传 | 大小:1kb | 下载:1

[绘图程序ReadObj

说明:请使用这个glut库(这个支持鼠标滚轮),而且这个导入很粗糙,只支持纹理图是bmp格式的,而且对obj还有一定要求 所以HandleObj就是为了预先处理obj的,使用很简单,直接将3dmax制作的obj(必须用三角形导出,呵呵,所以说很粗糙了)拖到它上面即可 纹理图必须和obj,mtl放在一个文件夹下(这么做,纯粹为了使用相对路径,移植性好)-Please use this glut Library (this support
<尹俊> 在 2025-04-28 上传 | 大小:20.38mb | 下载:1

[绘图程序matlab

说明:三站平面时差定位的MATLAB仿真和GDOP图-Three stations MATLAB simulation plane TDOA and GDOP Figure
<Jake> 在 2025-04-28 上传 | 大小:8kb | 下载:1

[绘图程序leachSEP

说明:路由协议LEACH 和路由协议SEP协议的比较仿真。-Routing protocols and routing protocol LEACH compare simulation SEP protocol.
<chuanqi> 在 2025-04-28 上传 | 大小:3kb | 下载:1
« 1 2 ... .27 .28 .29 .30 .31 832.33 .34 .35 .36 .37 ... 842 »

源码中国 www.ymcn.org