资源列表

« 1 2 ... .59 .60 .61 .62 .63 3264.65 .66 .67 .68 .69 ... 4311 »

[VHDL编程VHDL

说明:数字系统设计中的全加器、10进制计数器、2-4译码器、摩尔状态机、2-1路选择器的源代码-Digital System Design full adder, 10 hexadecimal counter ,2-4 decoder, Moore state machine ,2-1 MUX source code
<李帆> 在 2025-02-03 上传 | 大小:880kb | 下载:0

[VHDL编程FPGA_Design_experience

说明:讲解了在FPGA中时序设计时应该注意的问题,并分享了设计经验-On timing in the FPGA design should pay attention to the issue and to share the experience of the design
<zw1292> 在 2025-02-03 上传 | 大小:880kb | 下载:0

[VHDL编程Taxi-automatic-billing

说明:出租车自动计费系统的verilog程序代码-Taxi automated billing system verilog code
<刘新> 在 2025-02-03 上传 | 大小:879kb | 下载:0

[VHDL编程xge_mac

说明:10G MAC ip核源码其中包含了三个版本。经过测试正确无误。-======================== 10GE MAC Core ======================== ------------------------ 1. Directory Structure ------------------------ The directory structure for t
<xuchao> 在 2025-02-03 上传 | 大小:878kb | 下载:0

[VHDL编程1

说明:一个完整的雷达系统仿真MATLAB程序,非常具有参考价值-A complete radar system simulation MATLAB programs have great reference value
<老何> 在 2025-02-03 上传 | 大小:878kb | 下载:0

[VHDL编程lcd

说明:1602是目前最常用的显示器件,本例是通过verilog 代码实现1602的显示-1602 display
<易阳威> 在 2025-02-03 上传 | 大小:880kb | 下载:0

[VHDL编程m_seq

说明:产生长度为15的M序列,将m序列产生的数据作为输入,送入一个序列检测器,该序列检测器在检测到连续的“1010”时,送出一个时钟周期宽度的指示信号-15 m_sequence ,and can test"1010"
<周游> 在 2025-02-03 上传 | 大小:878kb | 下载:0

[VHDL编程ethernet

说明:一个典型的以太网的VHDL程序,非常有参考价值!! -A typical Ethernet VHDL program, a very valuable reference! !
<崔凯华> 在 2025-02-03 上传 | 大小:878kb | 下载:0

[VHDL编程DS18B20

说明:基于FPGA温度传感器DS18B20的Verilog设计-Verilog design based on FPGA temperature sensor DS18B20
<yuyu> 在 2025-02-03 上传 | 大小:878kb | 下载:0

[VHDL编程Quartus_II_9.0pojieshuoming)

说明:文件列表
<sinha> 在 2025-02-03 上传 | 大小:879kb | 下载:0

[VHDL编程FPGADisplay

说明:由ISE开发的FPGA工程文件,显示相关,包括视频接口,用Verilog开发,可以参考学习-ISE developed by the FPGA engineering documents, display related, including video interface, using Verilog development, you can refer to learning
<YL> 在 2025-02-03 上传 | 大小:879kb | 下载:0

[VHDL编程motor

说明:利用FPGA控制步进电机驱动器ULN2003来控制四相五线步进电机(FPGA stepper motor driver ULN2003 is used to control four phase and five wire stepping motors)
<尼采大大 > 在 2025-02-03 上传 | 大小:878kb | 下载:0
« 1 2 ... .59 .60 .61 .62 .63 3264.65 .66 .67 .68 .69 ... 4311 »

源码中国 www.ymcn.org