资源列表

« 1 2 ... .22 .23 .24 .25 .26 27127.28 .29 .30 .31 .32 ... 33934 »

[DSP编程weiji

说明:利用TS编程软件利用8255编写程序,在实验箱上实现8个LED同时显示15-11-05。-Use TS programming software uses 8255 programming, implemented on experimental box 8 LED display 15-11-05 simultaneously.
<邱宇> 在 2024-10-12 上传 | 大小:1024 | 下载:0

[单片机(51,AVR,MSP430等)TLE5012B

说明:TLE5012B的访问程序,基于STM32 SPI接口编写-TLE5012B Driver STM32 SPI PORT.
<xiaofei> 在 2024-10-12 上传 | 大小:2048 | 下载:0

[单片机(51,AVR,MSP430等)LSM6DS33

说明:LSM6DS33 驱动代码,基于STM32编写,6轴加速度计和陀螺仪驱动-LSM6DS33 Driver Based on STM32 SPI PORT
<xiaofei> 在 2024-10-12 上传 | 大小:13312 | 下载:0

[其他嵌入式/单片机内容UART_VERLIOG

说明:verilog写的UART串口-uart write by verilog.........................................
<黄靖宇> 在 2024-10-12 上传 | 大小:2048 | 下载:0

[微处理器(ARM/PowerPC等)USB

说明:STM32中USB协议例程,具体需要用到PortHelper上位机接受数据-STM32 s USB Protocol,when you need receive the data stm32,you need download a software named PortHelper
<hehai> 在 2024-10-12 上传 | 大小:1628160 | 下载:0

[微处理器(ARM/PowerPC等)AR8031_33_REF_DESIGN_V1.1

说明:AR8031/33 Reference Design 参考设计原理图-AR8031/33 Reference Design
<linyq> 在 2024-10-12 上传 | 大小:75776 | 下载:0

[嵌入式/单片机编程ch02

说明:c++ primer 第五版 习题解答源代码-Primer c++ fifth version of the source code to answer questions
<葛淼> 在 2024-10-12 上传 | 大小:2048 | 下载:0

[其他嵌入式/单片机内容i2c

说明:iic驱动的代码,包括IIc总线驱动,IIc核心,IIc设备驱动,还有部分驱动的算法实现及其数据结构,包含了pcf8574,pcf8575,pcf8591,tps95010等芯片的代码。-iic driver code, including the bus driver IIc, IIc core, IIc device drivers, there are some driven algorithms and data structu
<邹修荣> 在 2024-10-12 上传 | 大小:303104 | 下载:0

[单片机(51,AVR,MSP430等)RTD2025L_M170EN04-17

说明:2025乐华17寸 程序!对好屏幕型号!不能错的!RTD2025L_M170EN04_DO8L_SXGA_NA_5key_Bri=120-program! Screen models for good! Can not be wrong
<张春雷> 在 2024-10-12 上传 | 大小:65536 | 下载:0

[微处理器(ARM/PowerPC等)Sprinter_Melzi

说明:粗红线接HOTEND 白色的接ETEMP 风扇线接FAN,黑色接gnd 以上是喷头的 热床黑色接HOTBED 白色接BTEMP-Thick red wire HOTEND White then ETEMP Fans line connected FAN, black pick gnd These are the nozzle Hot bed of black pick HOTBED W
<star> 在 2024-10-12 上传 | 大小:86016 | 下载:0

[微处理器(ARM/PowerPC等)library

说明:脱机打印,首先都是要把gcode文件放到SD卡上,方法一是在电脑的软件里选择SD卡上的文件开始打印,然后就可以拔掉USB线了(当然不拔也可以,随便你。);方法二是把要打印的gcode文件重新命名成init.g,放在SD卡的根目录下,重新启动打印机(按reset按键或者断电重新上电都可以),机器就自动开始打印init.g这个gcode了。-There are two ways for offline printing, first of
<star> 在 2024-10-12 上传 | 大小:8474624 | 下载:0

[uCOS开发one-wire-lcd

说明:avr onewire shift register 74hc595
<nkarthi> 在 2024-10-12 上传 | 大小:16384 | 下载:0
« 1 2 ... .22 .23 .24 .25 .26 27127.28 .29 .30 .31 .32 ... 33934 »

源码中国 www.ymcn.org