资源列表

« 1 2 ... .38 .39 .40 .41 .42 1143.44 .45 .46 .47 .48 ... 1228 »

[串口编程clk_cfg

说明:Ti公司的cdce62005 spi总线配置,配置数值供参考-Ti Company, cdce62005 spi bus configuration, configuration values ​ ​ for reference
<geoff> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程iouart

说明:飞思卡尔单片机,用普通IO口,模拟串口通信,全双工方式。-Freescale microcontroller ordinary IO port analog serial communications, full duplex mode.
<Frank> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程vbCHUANKOU

说明:用vb写的两台计算机之间的串口程序,,速度快,算法简单,容易实现。-Vb write serial procedures between the two computers, fast algorithm is simple and easy to implement.
<孙晓妮> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程keyboard-scaning

说明:通过4X4矩阵键盘和数码管设置频率,按下确认按键后在AD9850输出相应的频率-keyboard scan
<qitiantian> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程TEL13796088061

说明:在12864液晶上显示一行汉字单片机爱好者和TEL13796088061-In 12864 a line of Chinese characters shown on the LCD MCU lovers and TEL13796088061
<qitiantian> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程8025-driver

说明:具有IIC接口的时钟芯片RX8025的驱动代码,模拟IIC时序。-Driver code of RX8025 which have IIC interface,the code is simulate the IIC timin
<北极星> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程7718Driver

说明:高进度AD采样芯片AD7718的驱动代码,模拟ISP接口-High progress AD sampling chip AD7718 s driver code,simulate ISP interface
<北极星> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程20130508

说明:modbus 用c语言实现了dsp2812与触摸屏的通讯,亲自试验成功-modbus with the c language the dsp2812 touch screen communication, personally successfully tested
<小霍> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程I2C_SoloMaster_Controler_02

说明: 本模块是通用的I2C Master控制器。 它支持3种模式:单纯写N次,单纯读N次,先写一次,然后读N次。 本模块的读写只是从I2C的角度,因此,对所有的DataIn, 本模块均当成传送的数据,具体在Slave那边的定义,由上层模块处理。-I2C Master
<李恩明> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程chuankoujiemian

说明:matlab GUI 的串口界面 可以将单片机板子上的温度值传到pc机的界面上以图形形式显示,并且检测一会后会计算平均温度等并显示。-matlab GUI microcontroller serial interface board can be reached on the pc-temperature values ​ ​ are displayed graphically on the screen, and
<崔微> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程SCI

说明:28335串口测试开发历程 C++编程 CCS运行-28335 serial test
<lupan> 在 2024-09-20 上传 | 大小:2048 | 下载:0

[串口编程Graph-serial

说明:Get data from file or RS232 and create graph
<Igor> 在 2024-09-20 上传 | 大小:2048 | 下载:0
« 1 2 ... .38 .39 .40 .41 .42 1143.44 .45 .46 .47 .48 ... 1228 »

源码中国 www.ymcn.org