搜索资源列表
UART
- MCU串口接收源码 通用于各MCU 带CRC校验-MCU-source general-purpose serial port to receive at all MCU with CRC Checksum
51SComDriver
- 一套比较完整的51单片机C51串口通信驱动程序，其中包括 （1）串口初始化，晶振为11.0592M，方式1 波特率300－57600； （2）串口输出一个字符(非中断方式)； （3）串口输出一个回车换行； （4）串口输出一个字符串（非中断方式）； （5）串口接收一个字符(非中断方式)； （6）串口接收一个定长字符串(非中断方式，只用于字符需有一个的idata字符串数组)； -Relatively comple
Soft20060207145602422
- vb实现的串口接收数据的源码.相当不错哦-vb realize the serial receive data source. pretty good, oh
comm0
- 用VB编写的一个用于串口接收和发送的一个小程序，可以用的-VB prepared using a serial port receive and transmit for a small procedure, can be used
master485
- 用485实现单片机之间的串行通信。 主机部分发送从机地址，等待从机响应，从机准备好就发数据,发完就接收从机的响应，接受成功就跳出循环，否则重发 系统时钟为11.059MHZ时，设定串口波特率为9600bit/s串口接收中断允许，发送中断禁止，设定定时器中断允许-With between 485 to achieve single-chip serial communication. Host part of the address
MATLAB_serial
- matlab串口通信,在MATLAB环境下编程实现串口接收数据-matlab serial communication, in the MATLAB programming environment Serial receive data
51SCOM
- 51单片机串口测试程序(KEIL C51)，将串口接收到数据显示到数码管上，很方便直观看到接收数据是否正确-51 Single-chip serial test procedure (KEIL C51), will receive the serial data into a digital tube, it is easy to see intuitively receive data is correct
COMTEST_7_14
- 通过串口接收和发送十六进制数据并在界面中显示。-Through the serial port receive and transmit data and hexadecimal display interface.
T232
- 全速运行程序，可看到串口调试助手的接收区显示“41 42 43 44 45 46 47 48”。手动发送“0102030405060708091011”，打开WATCH窗口可看到50H~5AH地址单元的值为“0102030405060708091011”，请注意50H单元是串口接收数据起始存放地址，70H单元是串口接收数据结束存放地址。-Run the program at full speed, can see the serial
serial-nrf9e5
- nrf9e5带超时无线收发：从串口接收数据（靠超时判断而不是字节判断），无线发送后，接收端将数据显示在串口。-nRF9E5 with overtime wireless transceiver: receiving data from the serial port (rather than relying on overtime to determine byte judge), wireless send after the rec
RS232C_step-motor
- 本程序为MCU端程序，单片机根据串口接收到的不同字符，来实现启动/停止步进电机，改变其转向，转速等动作。-This procedure for the MCU-side procedures, single-chip serial port to receive in accordance with the different characters to achieve the start/stop stepping motor, to
async_receiver
- 算法非常不错的RS232异步串口接收程序原代码-Algorithm are very good procedures RS232 asynchronous serial receive the original code
Porttest
- 一个串口调试助手,可以将串口接收到的数据筛选并保存到数据,别保存数据到文件等.-A serial debugging assistants can receive serial data to the data screen and save, do not save data to files.
serialportreceive
- 从串口接收数据，后经过计算显示到数字和波形界面上的labview程序，可以进行从0x800000H到0XFFFFFFH数据的十进制小数显示和接收。-From the serial receive data, calculated after the show to digital and waveform labview interface procedures can be carried out to 0XFFFFFFH from
serial_Simulation
- 单片机IO口模拟串口（接收+发送） 环境：STC单片机+KEIL2 使用单片机的IO口模拟串口。其中分别包含模拟串口接收数据和模拟串口发送数据两个测试程序。 另外，程序附加说明中对网上流传的一个不错的模拟串口代码提了一些改进建议，并说明了测试程序应用于实际工程需要注意的几个地方。-Simulation of Single-chip Serial IO port (receive+ send) Environment: STC
uart
- 51单片机 串口接收发送 都用到中断 全双工 采用C语言-51 MCU serial port receive interrupt is used to send both full-duplex using C language
CharTerminal
- 本例主要使C++的MSComm控件编写串口程序，串口接收程序-Export to receive program
CharTerminal
- 设置串口属性，并打开串口接收从串口进入的数据。-Set serial port properties, and open the serial port to receive data from the serial port of entry.
VC6Comm
- 在VC++6.0中用MSComm控件编程，可以实现串口接收数据和发送数据，数据分别显示在接收框和发送框中。-In VC++6.0 using MSComm control program can be achieved to receive serial data and sending data, the data shown separately in the receiver box and sent box.
str
- 使用msp430f413软串口接收数据并写入flash中-Use msp430f413 soft serial receive data and write to flash in